Модули дискретного ввода/вывода

Модули дискретного ввода/вывода Advantech ADAM-5000, включая ADAM-5056, имеют изоляцию и функции защиты от отказа для создания надежных систем. Эти модули дискретного ввода/вывода, включая ADAM-5056, включают модули с шестнадцатью каналами дискретного вывода, восемью полностью независимыми изолированными каналами, и 32-канальными изолированными модулями дискретного вывода.

• Количество каналов ввода: 3
• Эффективное разрешение: 16-бит
• Схема подключения: 2-, 3- или 4-проводная
• Типы входного сигнала: Pt 100 или Ni термосопротивление
• Напряжение изоляции 3000 В пост тока
• Частота выборки: 10 выборок/сек
• Точность: ±0,1% и выше

• Количество каналов: 16
• Напряжение входа: 30 В максимально
• Тип схемы: ток возбуждения - 0.5 мА
• Потребляемая мощность: 0,4 Вт (стандартно), 0,53 Вт (максимально)

• Количество каналов: 16
• Напряжение ввода: 30 В максимально
• Тип схемы: ток возбуждения - 0.5 мА
• Потребляемая мощность: 0,5 Вт (стандартно), 0,84 Вт (максимально)
• Светодиодные индикаторы

• 16-channel
• 50 Vmax Input Voltage
• 2500 Vdc Optical Isolation
• 70 Vdc Over Voltage Protection

• Channels: 8
• Digital input level: Logic level 0: +1 V max.
• Isolation voltage: 5000 VRMS
• Power consumption: 0.27 W (max)

The ADAM-5052 provides eight fully independent isolated channels. All channel designed with 5000 VRMS isolation to prevent ground loop effects and the damage from power surges on the input lines.

• Digital Input Channels:32
• Digital Input Channel I/O Type:DI, 24VDC (Sink/Source)
• 2500VDC Isolation voltage protection
• Only for ADAM-5560 series

• 16-channel
• I/O Type: 8 DO & 8 DI
• Optical Isolation: 2500 Vdc
• Power Consumption: 0.68 W (Typical)

• Channels: 16
• Operating voltage: 30 Vmax
• Digital output: Open collector to 30 V, 100 mA max. load
• Power consumption: 0.25 W (typical); 0.53 W (max.)
• Power dissipation: 300 mW for each channel

The ADAM-5056 features sixteen digital output channels. The digital outputs are open-collector transistor switches that you can control from the ADAM-5000 main unit. You also can use the switches to control solid-state relays.

• Channels: 16
• Operating voltage: 30 Vmax
• Digital output: Open collector to 30 V, 100 mA max. load
• Power consumption: 0.5 W (typical); 0.84 W (max.)
• LED indicator: On: Output logic level "1"
• Output status hold function
• Power dissipation:300 mW for each channel

The ADAM-5056D features sixteen digital output channels with LED indicators. The digital outputs are open-collector transistor switches that you can control from the ADAM-5000 main unit. You also can use the switches to control solid-state relays.

• 16-channel
• Optical Isolation: 2500 Vdc
• Over Voltage Protection: 70 Vdc
• Power Consumption: 0.6 W (typical)
• Power Dissipation: 300 mW

• 16-channel
• Optical Isolation: 2500 Vdc
• Over Voltage Protection: 70 Vdc
• Power Consumption: 0.6 W (max.)

• 16-channel
• Optical Isolation: 2500 Vdc
• Over Voltage Protection: 70 Vdc
• Power Consumption: 0.6 W (max.)

• Contact rating: AC: 125 V @ 0.6 A; 250 V @ 0.3 A
• Breakdown voltage: 500 VAC (50/60 Hz)
• Relay on time (typical): 3 msec.
• Relay off time (typical): 1 msec.
• Total switching time: 10 msec.
• Insulation resistance: 1000 MW minimum at 500 VDC
• Channels:2 x form A , 4 x form C

The ADAM-5060 relay output module is a low-cost alternative to SSR modules. It provides 6 relay channels, two of Form A and four of Form C.

• Supports Modbus/RTU protocol
• High Power Relay Output : 250Vac@5A, 30Vdc@5A
• 8-channel Relay Output
• 8 form A channels
• Jumper setting for output status when reset
• 8 LED indicators

ADAM-5069 is designed for on/off control in high-voltage applications. The major feature of ADAM-5069 is the power relay rating at 240 V AC and 5 A. This range can satisfy most requirements for driving externally controlled devices such as lights, fans, alarm systems, and various electronic devices in industrial automation, security, building and home automation applications. ADAM-5069 provides a jumper setting for output values. This jumper can be set to clear or keep output values when reset. To easily identify the module’s status, it has been designed with 8 LED indicators. It also provides eight form A channels, and when combined with selected controllers, it will provide the Modbus/RTU protocol for standard communication requirements.